ANO NA ANG NABAGO MO SA GUCHI MO???

PIPE PA LANG

GUYS PWEDE N KAYO MAG-POST

My Baby is still all stock, except for the chains, sparks and sprockets. But top speed is still 130kph.

My upcoming projects will be a tire hugger, new fairing designs, and a single underseat CF pipe.

i just change my pipe recently....my next plan is to complete first my safety gears then...hopefully, i can have my Kryptonite(my guchi's name) port & polish as per sir DZDZ.... 

my hurc's name is "akira", sa engine additional clutch plate, open pipe n carb, irridium spark plug, 16x39 spraks, 120x80 rear wheel 90x80 front wheel, lift up mono shock, malossi induction, top speed achieved 140kph(stock pa xa dt time n my vibrate pa),
as of now inaccurate ung speedo nya dahil oversize na ung front wheel kaya circumference nya nag change kya reading sa speedo inaccurate na. next project tire hugger/rear inner fender, powder paint ng swing arm, but i want to convert it to 6 speed if there is a chance, possible namn gawin un sa hurc e, basta meron available na parts. port n polish?, polish lng cguro, kasi parang nka port n raw ung hurc, bka ma lose compression mahirap na, ung manifold natin hindi align sa carb n cylender head, un dapat bigyan pansin, mahirap din subukan kasi baka macira ung manifold, but guys nagawa na yan sa hurc ni dzdz, punta kyo sa sucat my fren mekaniko kami na favs nya ang guchi bikes, actully 2 unit nya guchi, ung spider(x1 yamaha type), xa mods ng hurc ni dzdz.

quickstrike wrote:my hurc's name is "akira", sa engine additional clutch plate, open pipe n carb, irridium spark plug, 16x39 spraks, 120x80 rear wheel 90x80 front wheel, lift up mono shock, malossi induction, top speed achieved 140kph(stock pa xa dt time n my vibrate pa),
as of now inaccurate ung speedo nya dahil oversize na ung front wheel kaya circumference nya nag change kya reading sa speedo inaccurate na. next project tire hugger/rear inner fender, powder paint ng swing arm, but i want to convert it to 6 speed if there is a chance, possible namn gawin un sa hurc e, basta meron available na parts. port n polish?, polish lng cguro, kasi parang nka port n raw ung hurc, bka ma lose compression mahirap na, ung manifold natin hindi align sa carb n cylender head, un dapat bigyan pansin, mahirap din subukan kasi baka macira ung manifold, but guys nagawa na yan sa hurc ni dzdz, punta kyo sa sucat my fren mekaniko kami na favs nya ang guchi bikes, actully 2 unit nya guchi, ung spider(x1 yamaha type), xa mods ng hurc ni dzdz.

wow sir...lufet nmn ng hurc mo...gusto ko gayahin...isa-isa sana...

i encourage all guchi riders to post here!!

when i bought my gutchi 100kph lang talaga ang top speed tapos sobrang lakas ng vibration, then when i replaced rear sprocket with a 39t and used an oversized air filter napapaabot ko na sya ng 120kph and halos wala na yung vibration.

.. next project open pipe and 120X70 rear time and will also try to use a 36teeth rear sprocket.

nice to hear from you sir con....hope we can meet sooner...i think marilaque ride can make us the calamba-sucat-tanza hurc riders grand EB

sama ako d2 for sure. hehehehhe! kita kits tayo hurricane riders!

isusulong naten ito after the club officers election... masaya at maganda ito...

up ko lang po ang thread na ito...

PAKI-POST NAMAN PO KUNG PANO GUMAWA ,.NG IMPROVISED INDUCTION,...STEP BYSTEP PO SANA...